A user often notices the LE error without looking on a display of the Samsung washing machine. The point is that the puddles on the floor are impossible to ignore. What are the causes of the leak? Is it possible to solve the problem without the help of a specialist?
The main reason for the LE error code in Samsung washing machine
The LE fault ‘s appearing on the screen signals about the leaking tank. The manufacturer repeatedly changed the error codes. Some Samsung front load washer models show the LE1, Е9 (devices, manufactured before 2007) or the LC error code. The fault codes are identical to each other.
The water from the washing machine leaks on the floor. Therefore, a user can determine the failure cause visually. But in rare cases, it is not possible to detect a failure in work by external signs. For example, the washing machine seems to be in order, although the display shows an error.
How to determine the fault
If the pressure switch for a short period has detected a decrease in water volume more than four times, the washing will stop. The technique shows the corresponding code on display.
The washing machine stop when the drain hose is damaged prevents overheating of complex electronics. Replacing consumables is cheaper than replacing a burnt outboard.
Some models are equipped with aqua-stop. In such units, a particular sensor monitors the integrity of the tank and the level of water filling. According to the principle of operation, it looks like a float, located at the washing machine bottom. If the process of collecting and draining the water is broken, the pallet overflows the liquid, raising the sensor. The technique interrupts its operation, and the washer shows the LE error.
In some cases, it is possible to remove the LES error without a master. To do this, you need to find a leak place. There are several weak elements in the washing machine. It is mainly about hoses (for water draining and drum connecting). The compressor can also leak, damaging small items that get into the washer. In this case, the washing spoils clothes in the drum, too.
If the new Samsung technique shows the LEI error, it is possible that the hose’s tightening was weak. To reset errors, provide proper assembling.
The table will help you to understand what leads to malfunction and how to fix the problem.
| Malfunction | Possible reasons | What to do |
| A user notices water under the technique. The display shows the LE error code. | Mechanical damage to the seal cuff or branch pipe for water discharge. | You can glue small cuts, but more often users have to change the damaged part. It requires the help of a specialist. |
| The washing does not start. When a user tries to run the technique, the LE error code appears. | Failure of the pressure switch. | If blowing the clogged part of the tube doesn’t solve the problem, a replacement is necessary. |
| LE lights up when changing the washing process: passing to spinning or rinsing. | Perhaps the electronic indicator circuit has failed. | In many cases, the board soldering can restore the correct operation. If the processor has burnt out completely, you need to buy a new one. |
| The washer, equipped with aqua-stop, starts working. Then, it issues the LE error code. | There is a possibility of incorrect operation of the sensor with a working technique. | Replace the part. |
| The fault indicator disappears for a while and then occurs again. | Damage to the wiring of the washing machine. It has frayed, spoiled or worn out. | A user can try twisting the wires or replacing the cable with a new one. |
What does LE mean on my Samsung washer?
The LE error code occurs when the pressure switch senses a sharp decrease in the volume of water in the drum - more than a quarter. Common causes of leakage are damage to the drain hose, nozzle, or rubber seals. Sometimes an error is caused by a broken level sensor or a burnt control board.
What is LE in the washing machine Samsung?
A LE error indicates that the pressure switch detected a sudden drop in water level. There may have been a leak due to damage to the components of the drain system. A failure in the operation of the pressure switch is not ruled out, caused by a clogged tube or mechanical malfunction. Slightly less often, it happens the primary module failure.
How do I fix the error LE on my Samsung washer?
To fix the LE error, find and repair the leak. Problem areas - rubber seals, pipe, and drain hose. If there is no leak, check the pressure switch. At the same time, inspect the wires leading to the mainboard and the control module itself. If there is damage, restore the contacts, solder the burned tracks. Replace inoperative items.